The GearMate Bracket Set is an essential component needed to use your GearMate organiser. This set allows you to configure your components to suit your gear organisation needs.
Note: The Bracket Set requires the GearMate SteadySpine, sold separately.
The GearMate Bracket Set enables effortless customisation of your storage system by allowing quick attachment and detachment of brackets to the GearMate SteadySpine within seconds. This design offers maximum flexibility, enabling you to arrange your storage setup according to your specific needs. Compatible with all GearMate accessories—including SteadyBins (small, medium, and large) and Hooks—the brackets ensure a secure and organised storage solution.
SteadyBracket: 1 x Small Bracket, 1 x Medium Bracket, 1 x Large Bracket
The GearMate Bracket Set works by slotting into the GearMate SteadySpine, and allows other GearMate components to slide on and off effortlessly. The GearMate Bin Kits come with the correct sized bracket included.
Important: You will need the GearMate SteadySpine to use the Bracket Set. The SteadySpine is included with the ProFlex Range, but will need to be purchased separately if installing with the Classic Range.
JOIN WAITLISTProvide us your email. We’ll contact you when this item becomes available again.
READY TO RIDE
Customise your GearMate, your way.
Slide & Drop System
GearMate Bracket Set
The GearMate Brackets give you the creative freedom to customise your setup. Simply slot your brackets into the SteadySpine in whatever configuration you choose.
What's your favourite GearMate features? Simple Installation, Organisation, Easy to Use
5つ星のうち5
2日前
Superb
Took a while to getting the bike racks installed but now that they are in use cannot be happier. Has made garage access so much easier and with gear mate bracket set makes it nice and easy to have the accessories stored close by and organised. Intergrated with the rack itself is very clever.
No, you can load and unload the bike at any angle provided that the central pivot bar nuts are set to the factory setting of 5nM.
No, it's not possible to lock the rack solid in one position. You can tighten the nuts sufficiently that the rack will be very hard to pivot which will effectively hold it in the one position. To do this you need to remove the 2 plastic mounting bracket covers (end caps) and tightening the 2 nuts that attach the central pivot bar to the mounting brackets. We recommend you check your fixings to your wall carefully and make sure they are very secure if you do this as any pressure sideways will put extreme pressure on the mounting brackets fixings.
It really depends on the width of your handlebars and the pedals. It will fold until the handlebars touch the wall but not quite 90 degrees or flat to the wall. For a normal road bike bar, we would allow about 400mm or around 16 inches, and for a MTB with wider bars probably around 1m or 39 inches (give or take).
The Fender Racks will suit exactly the same bikes as the Classic Rack except the Fender rack will also work with bikes that have fenders or mudguards, whereas the Classic is only suitable for bikes without fenders and mudguards. The Fender rack will also only accommodate for bikes up to 25kg/55lbs.
One of the main features of our design is the fact that it is the most suitable rack for carbon wheels. There is less pressure on the bike than riding it and it is certainly better than hooks. The wheel is cradled between the two V-shaped cradling points created when the arms are folded down and the tire cushions the wheel and bike. There should be absolutely no need to do any maintenance on your rims or wheels if you use a Steadyrack.
Steadyracks are actually the perfect solution for storing carbon frame bikes and wheelsets! This is because our racks cradle the whole front wheel tire, meaning there is no direct contact with the wheelset or bike frame. Additionally, there is less risk of damage from and to surrounding bikes as the racks are made to pivot and are hung by rolling the bike into the cradle instead of lifting the bike onto a hook.
Yes! This is a common concern for many bike owners with these types of brakes and suspension. When your bike is hung up vertically, the fluid in your forks will run towards the seals and keep them lubricated. This will prolong their use, so it's actually good for your bike and forks to hang it vertically on our bike racks. If you have hydraulic brakes on your bike the fluid will run down when the bike is hung, so we advise pumping the brakes a few times when you take the bike off the rack if it's been there for a while. The shocks shouldn't leak when the bike is hung up, however if they do it's a good indication that the seals may need replacing. Read our blog post for more information about storing bikes with hydraulic brakes in Steadyracks.
